Durotech

Duroflex Tank – Flexible Cementitious Membrane

Regular price
$229.95 AUD
Sale price
$229.95 AUD
Regular price
Shipping calculated at checkout.

Prices shown exclusive of GST.

Online stock available
Durotech Duroflex Tank provides flexible cementitious waterproofing for concrete and masonry in wet and damp conditions. This two-part membrane bonds to clean, pre-dampened mineral substrates without a primer and suits water features, tanks, internal wet areas, balconies, planter boxes and retaining walls. It accepts compatible tiles, renders, texture coatings and solvent-free paints once cured, supporting a practical transition from waterproofing to finish. Use the specified junction and joint detailing, and apply both coats at the required build. For tanks and other immersed areas, confirm the filling time with Durotech because the current data sheet contains conflicting immersion guidance.
Calculating estimated delivery

H2O AI Product Support

Technical and product guidance for the item you’re viewing.

  • For internal wet areas, balconies/decks/podiums, parapets, planters, retaining walls, water features and tanks.
  • Bonds to clean, sound, pre-dampened concrete, masonry, render, screed and other cement-based mineral surfaces without a primer. Remove ponding/surface water.
  • Detail movement joints with Durofabric Joint Seal Tape; reinforce repaired non-moving cracks with Duro RF Fabric as specified.
  • For positive-side waterproofing, embed the specified joint seal tape at wall/floor junctions. Negative-side work requires the recommended waterproof fillet detail.
  • Use the specified two-coat application; compatible tile, render, texture and solvent-free paint finishes can be applied to the cured membrane.
  • Confirm immersion/filling readiness with Durotech due to conflicting timings in the current sheet.
  • Part A 20 kg powder + Part B 10 L resin; mix 2 kg powder to 1 L resin. Do not present this as a verified 30 kg or 30 L mixed kit.
  • Coverage is 1 L of mixed compound/m² per coat; two coats require 2 L/m² in total. The specified nominal wet film thickness is 1 mm per coat.
  • The TDS does not state a verified mixed yield for the supplied kit; a kit-area calculator has therefore not been configured.
  • Pot life approximately 45–60 minutes in ambient conditions below 20°C.
  • The application section says recoat when touch dry, potentially 30–60 minutes; the drying table lists 1–2 hours. Conditions and surface porosity affect drying.
  • At normal 20°C conditions, listed dry time 6–8 hours; allow 48 hours before light foot traffic.
  • Immersion guidance conflicts: the drying table lists 21 days, while another paragraph gives 5–7 days before filling. Obtain Durotech confirmation for the project.
  • Application/surface temperature 5–30°C.
  • TDS reports tensile strength >1.4 MPa and adhesion to concrete >1.5 MPa; no unverified Australian Standards classification is claimed.
  • Shelf life: powder and liquid six months unopened; store dry at room temperature, protected from humidity/frost.

Duroflex Tank FAQs

Does Duroflex Tank need a primer?
No primer is required on the suitable mineral substrates listed in the TDS. Surfaces must be clean, sound and damp or pre-wetted, with no surface or ponding water. Primer-free use does not remove the need for mechanical preparation and defect repairs.
What is the coat coverage?
Apply approximately 1 L of mixed compound per m² for each coat, with two coats requiring 2 L/m² total at the stated nominal wet-film build. The powder is supplied in kilograms and resin in litres; they cannot be added together to calculate mixed kit litres.
How long before I fill a tank or water feature?
The current Durotech TDS is inconsistent: its drying table states 21 days for immersion, while another paragraph states 5–7 days before filling. Confirm the applicable filling time with Durotech before scheduling immersion. The 6–8-hour dry time is not a filling time.
When can I apply the second coat?
The application section permits recoating once the first coat is touch dry and mentions 30–60 minutes; its drying table lists 1–2 hours at normal 20°C conditions. Check that the first coat is suitably dry and confirm the timing for the site conditions rather than relying on a universal fast-recoat claim.
Can tiles or render be applied over it?
Yes, once the membrane is cured, using compatible materials. The TDS recommends Durotile Pro for direct tile adhesion and enhanced renders/screeds using the specified bonding additive approach. Follow the full finish-system requirements.
What needs detailing before coating?
Movement joints need the specified Durofabric Joint Seal Tape. Repair and reinforce non-moving cracks with the nominated fabric, and complete wall/floor junctions or negative-side fillets to the manufacturer’s detail before the field coats.

Need Technical Advice?

Not sure if this product is suitable for your project?

Our technical team provides independent advice on product selection, compatibility and waterproofing systems.

Independent product advice backed by real-world waterproofing experience.

Contact Technical Support
(07) 3667 9878

Monday–Friday
7:00 am – 3:00 pm AEST

Warehouse Stocked
Fast Australia-wide Delivery
Expert Technical Advice
Secure Checkout

Frequently Purchased Together

These popular picks are often added by trade professionals to complete their project kits.