Lower-maintenance internal areas
Shopping malls, food courts, offices, hotel lobbies, residential living areas and internal stairs not frequently exposed to water.
Stellmann
Stellmann Non-Slip Clear PRO
- Regular price
- $430.50 AUD
- Sale price
- $430.50 AUD
- Regular price
-
Shipping calculated at checkout.
Prices shown exclusive of GST.
Out Of Stock
- Choose P3, P4 or P5 slip resistance
- Transparent finish preserves the existing surface
- Water-based two-component polyurethane
Couldn't load pickup availability
Overview & Features
- Single-coat application over Stellmann Clear Primer.
- Suitable for correctly prepared tile, stone, compatible coatings, timber, metal and glass.
- Touch dry in approximately 60 minutes; light pedestrian traffic after approximately 12 hours.
Application Guide
- 1. Clean and correctly prepare the substrate in accordance with the current Stellmann instructions; the surface must be clean and dry.
- 2. Apply Stellmann Clear Primer. The TDS specifies the primer is diluted 1:1 with water and allowed approximately 30 minutes to cure under standard conditions.
- 3. Mechanically mix Part A and Part B at 5:1 by weight. For the P5 variant, add the supplied non-slip aggregate strictly in accordance with the current manufacturer instructions.
- 4. Apply one even coat using the specified roller at approximately 72 g/m². Do not apply a second coat or back-roll unless the current manufacturer instructions expressly permit it.
- 5. Protect from water and traffic during cure. Typical touch-dry time is approximately 60 minutes and light pedestrian traffic is permitted after approximately 12 hours under standard conditions.
- 6. Do not apply where rain is imminent, relative humidity exceeds 85%, the substrate has excessive moisture or defective waterproofing, or where the coating will be permanently immersed.
Specifications & Standards
- Product type: clear anti-slip polyurethane coating system
- Chemistry: water-based, two-component polyurethane
- Slip-rating variants: P3, P4 and P5
- Kit coverage: up to 15 m²
- Mixing ratio: Part A : Part B = 5:1 by weight
- Application: one coat over Stellmann Clear Primer
- Typical application rate: approximately 72 g/m²
- Touch dry: approximately 60 minutes
- Light pedestrian traffic: approximately 12 hours
- Application temperature: 15–35°C
- Maximum relative humidity: 85%
- Water exposure: resists rain and condensation; not suitable for permanent immersion
- Finish: transparent / clear
Product Documents
Which Slip Rating Do I Need?
Stellmann Non-Slip Clear PRO is available in different slip ratings to suit different pedestrian environments. Select the rating according to the project conditions and required slip resistance.
Internal wet and amenity areas
Residential showers, bathrooms, kitchens, internal stairs, amenities, hotel bathrooms, hospital and aged-care bathrooms, and communal changing areas.
Outdoor and exposed pedestrian areas
Outdoor entries, walkways, external ramps, driveways, footpaths, car parks, balconies, verandas, courtyards, pool surrounds and communal showers.
Higher-risk sloped or commercial areas
External ramps and footpaths steeper than 1 in 14, undercover loading docks and commercial kitchens.
Online kit options: P3, P4 and P5. P3 Soft is included here as system-selection guidance but is not currently a purchasable Shopify variant. Contact H2O Technical if P3 Soft may suit the project.
Not sure which rating you need?
Ask H2O TechnicalSlip-rating requirements depend on the location, surface conditions and project use. Send us the application area and substrate and H2O Technical can help identify the appropriate system.
Choose by Application
Use these categories as an initial guide. The required slip classification must still be determined for the specific location.
Internal Wet Areas
- Bathrooms and showers
- Amenities
- Changing rooms
Generally associated with the relevant P3/P4 system depending on project requirements.
Balconies & Outdoor Areas
- Balconies and verandas
- Courtyards and walkways
- Outdoor entries
The TDS identifies P4 for many of these applications.
Ramps & Higher-Risk Areas
- External ramps
- Sloping driveways and footpaths
- Loading areas and commercial kitchens
P4 or P5 may be required depending on application and slope.
Commercial & Public Areas
- Hotel lobbies
- Shopping centres and food courts
- Offices and public amenities
Selection depends on wet exposure and the required slip resistance.
Add an editable surface or application image in the Theme Editor.
Slip Resistance Without Hiding the Existing Finish
A transparent topical coating designed to improve slip resistance while allowing the existing surface appearance to remain visible. A test area is recommended because substrate, sheen, application method and lighting can affect the final appearance.
- Transparent
- Water-based
- Dual-component polyurethane
- UV-resistant and non-yellowing
- Interior and exterior use
- Topical surface sealer that repels water
Important: This product is not intended to rectify failed waterproofing, rising damp or negative hydrostatic moisture conditions.
Suitable Surfaces
The TDS identifies compatibility with a broad range of properly prepared substrates used internally and externally.
Tiles & mineral surfaces
Tiles, ceramics, natural and engineered stone, marble, sandstone, terracotta, bluestone, slate and other porous stone materials.
Sheet & coated surfaces
Fibre cement, acrylic coatings, polyurethane coatings and epoxy coatings.
Other identified substrates
Timber, metal and glass, subject to preparation, adhesion testing and system assessment.
Adhesion and suitability must be confirmed where the surface contains unknown coatings, sealers, nano treatments or water-repellent treatments. Do not apply over nano or other repellent treatments without appropriate assessment and testing.
System Components
The complete installation is a prepared, primed and accurately mixed coating system—not coating alone.
Surface preparation
Thoroughly clean the substrate; remove dirt, dust, contamination, loose material and flaking coatings. Allow it to become completely dry.
Stellmann Clear Primer
Apply the nominated primer before Non-Slip Clear. Dilute 1:1 with water, apply a thin film, avoid puddling and allow approximately 30 minutes at room temperature.
Part A
Mechanically mix Part A at low speed for 5 minutes before use.
Part B
Measure and combine with Part A at 5:1 by weight using a clean vessel and electrical precision scale; mix at low speed for at least 5 minutes.
Slip-rating system
Use the system and particle component applicable to the nominated classification. P5/R12 specifically references Stellmann P5 particles.
Kit contents vary by selected rating. P5/R12 specifically uses the applicable Stellmann P5 particle system. Confirm the supplied components for the selected Shopify variant before application.
Typical Application Process
Follow the current TDS, Safety Data Sheets and installation manual. Complete a test area where substrate condition, adhesion or appearance is uncertain.
Clean
Remove dirt, dust, contamination, loose material and flaking coatings. Wash clean and allow the surface to become thoroughly dry.
Prime
Dilute Stellmann Clear Primer 1:1 with water. Apply a thin film without puddling and allow approximately 30 minutes at room temperature.
Mix
Mix by weight: Part A : Part B = 5 : 1. Pre-mix Part A, weigh accurately and mechanically mix the combined components at low speed for at least 5 minutes.
Apply
Apply one even coat at a nominal 72 g/m². Do not second-coat, dry roll or roll back into completed sections. Use mixed coating within 45 minutes.
Cure
Protect the area while curing. Temperature, humidity, porosity and application conditions affect drying and trafficability.
Part A + Part B Mixing Calculator
Enter the Part A weight. The 5:1 ratio is calculated by weight—not volume.
Required Part B40 g
Total mixed weight240 g
Use a clean vessel and electrical precision scale. Part B = Part A × 0.2; total mixed weight = Part A × 1.2.
Cure Timeline
Tack free90–180 min
Light pedestrian traffic12 hours
Full chemical cure5 days
Benchmark conditions: 23°C and 50% RH. Temperature, humidity and substrate porosity can alter cure times. The TDS also describes the coating as touch dry in approximately 60 minutes.
Application Conditions
| Air temperature | 15°C–35°C |
|---|---|
| Substrate temperature | 15°C–35°C |
| Relative humidity | Maximum 85% |
| Concrete moisture | Below 10% |
- Do not apply when rain threatens or RH is above, or likely to exceed, 85% shortly after application.
- Do not apply over faulty waterproofing, high substrate moisture, rising damp or negative hydrostatic pressure.
- Record substrate temperature, moisture, RH and dew point before application.
- Do not start in direct sun above 30°C; contact Stellmann Technical regarding HVLP spray application.
Avoid These Common Application Errors
Do not mix by volume
Measure Part A and Part B by weight using an electrical precision scale.
Do not double-coat
The non-slip system is a single-coat application.
Do not roll back
Overlapping or double application can leave a translucent or whitish appearance.
Do not apply to damp substrates
Confirm the surface is dry and within the stated moisture limits.
Assess repellent treatments
Nano sealers and other repellent treatments can prevent adhesion.
Do not coat failed waterproofing
This topical coating is not a remedy for underlying waterproofing failure.
Technical Performance
FinishTransparent; satin when roller applied and matt when spray applied.
SystemTwo-component polyurethane; Part A : Part B = 5:1 by weight; one coat.
Nominal spreading rateApproximately 72 g/m²; practical rates vary with roughness, porosity, method and conditions.
Weather and waterExcellent exterior exposure resistance; resists rain and condensation; not recommended for permanent immersion.
Traffic and heatSuitable for low, medium and high pedestrian traffic; dry heat resistance up to 120°C.
Clean-up and storageWater clean-up; shelf life 1 year unopened when correctly stored away from sunlight and frost.
Tested Slip Resistance
Stellmann Non-Slip Clear PRO has been tested in accordance with AS/NZS 4586:2013. The TDS lists Wet Pendulum Slider 96 classifications P3, P4 and P5, and Wet Pendulum Slider 55 classifications P3, P4 and P5. P5/R12 is available with the applicable Stellmann P5 particle system.
The required slip classification must be determined for the specific location. The selected system, application method and manufacturer requirements must be followed; purchasing a kit alone does not establish project compliance or guarantee the installed classification.
Before You Order
Confirm the following project details before choosing a kit and slip rating.
Existing surface type
Internal or external application
Approximate area in m²
Wet or dry exposure
Slope or ramp conditions
Required slip rating, if known
Existing coating or sealer
Moisture condition
Project location
If you are unsure which rating or kit is appropriate, send H2O Technical a photo of the surface and a short description of the application.
Get Technical AdviceTechnical Documents
Part A and Part B SDS fields are ready, but document links will remain hidden until the approved files are added in Shopify product metafields or these section settings.
Need Technical Advice?
Not sure if this product, slip rating or substrate preparation is right for your project?
Our technical team can help review the application area, surface condition and system selection.
Independent product advice backed by real-world waterproofing and construction experience.
Contact Technical Support
(07) 3667 9878
Monday–Friday
7:00 am – 3:00 pm AEST
Frequently Purchased Together
Compatible preparation, primer and application accessories for the selected system.